Hoist brakes or holding brakes

Hoist brakes are essential for crane safety

Hoist brakes are an essential safety feature of overhead cranes. Designed to hold a load when the hoist motor is not running, these brakes reduce the risk of falling loads that could result in injury and property damage.

This section specifies the performance requirements of hoist, or holding, brakes. It also calls for an additional control braking mechanism to prevent overspeeding – that is, to prevent hoists from exceeding a predetermined operating speed.

The Konecranes technical team can help you in your efforts to maintain a safe, productive operation by inspecting your equipment and performing needed service.

 

OSHA 1910.179 Overhead & Gantry Cranes Regulations

The following excerpt is taken directly from OSHA 1910.179.*

Brakes for hoists

  • Each independent hoisting unit of a crane shall be equipped with at least one self-setting brake, hereafter referred to as a holding brake, applied directly to the motor shaft or some part of the gear train.
  • Each independent hoisting unit of a crane, except worm-geared hoists, the angle of whose worm is such as to prevent the load from accelerating in the lowering direction shall, in addition to a holding brake, be equipped with control braking means to prevent overspeeding.

Holding brakes

  •  Holding brakes for hoist motors shall have not less than the following percentage of the full load hoisting torque at the point where the brake is applied.
    • 125 percent when used with a control braking means other than mechanical.
    • 100 percent when used in conjunction with a mechanical control braking means.
    • 100 percent each if two holding brakes are provided.
  • Holding brakes on hoists shall have ample thermal capacity for the frequency of operation required by the service.
  • Holding brakes on hoists shall be applied automatically when power is removed.
  • Where necessary holding brakes shall be provided with adjustment means to compensate for wear.
  • The wearing surface of all holding-brake drums or discs shall be smooth.
  • Each independent hoisting unit of a crane handling hot metal and having power control braking means shall be equipped with at least two holding brakes.

Control braking means

  • A power control braking means such as regenerative, dynamic or countertorque braking, or a mechanically controlled braking means shall be capable of maintaining safe lowering speeds of rated loads. 
  • The control braking means shall have ample thermal capacity for the frequency of operation required by service. 

 

Brakes for trolleys and bridges

  • Foot-operated brakes shall not require an applied force of more than 70 pounds to develop manufacturer's rated brake torque. 
  • Brakes may be applied by mechanical, electrical, pneumatic, hydraulic, or gravity means. 
  • Where necessary brakes shall be provided with adjustment means to compensate for wear. 
  • The wearing surface of all brakedrums or discs shall be smooth. 
  • All foot-brake pedals shall be constructed so that the operator's foot will not easily slip off the pedal. 
  • Foot-operated brakes shall be equipped with automatic means for positive release when pressure is released from the pedal. 
  • Brakes for stopping the motion of the trolley or bridge shall be of sufficient size to stop the trolley or bridge within a distance in feet equal to 10 percent of full load speed in feet per minute when traveling at full speed with full load. 
  • If holding brakes are provided on the bridge or trolleys, they shall not prohibit the use of a drift point in the control circuit. 
  • Brakes on trolleys and bridges shall have ample thermal capacity for the frequency of operation required by the service to prevent impairment of functions from overheating. 

Application of trolley brakes

  • On cab-operated cranes with cab on trolley, a trolley brake shall be required as specified under paragraph (f)(4) of this section. 
  • A drag brake may be applied to hold the trolley in a desired position on the bridge and to eliminate creep with the power off. 

Application of bridge brakes

  • On cab-operated cranes with cab on bridge, a bridge brake is required as specified under paragraph (f)(4) of this section. 
  • On cab-operated cranes with cab on trolley, a bridge brake of the holding type shall be required. 
  • On all floor, remote and pulpit-operated crane bridge drives, a brake of noncoasting mechanical drive shall be provided.

Konecranes Service can help determine if braking systems are operating up to specifications and make necessary repairs or replacements to raise the safety and productivity of your operation.

 

 

 

*The foregoing OSHA regulations are not intended to be a comprehensive overview of all applicable regulations pertaining to the designated topic. State laws may mandate different safety and maintenance standards. Accordingly, please consult applicable state laws as well as original equipment manufacturer specifications for further guidance. The statements and descriptions contained herein constitute the opinion/recommendation of the seller and are not intended to create any express warranties.